TOP
#2001 SealPeel is a transparent liquid at room temperature, and the dried film can be easily peeled off as a single film.
It is used for surface protection and waterproofing of goods.
The following three methods of application are available.
1.Applied by brush or roller
2.Spray application
3. Dipping (dobbing)
16kg can, 3kg can
| Appearance | Clear colorless liquid |
| Stinky | Aromatic smell |
| Boiling point | 86.5℃(toluene) |
| Specific gravity | 0.89 |
| Solubility | insoluble in water |
| Volatile | Existence |
| Flash point | -0.5℃ |
| Point of ignition | 415℃ |
1.When working indoors, use a well-ventilated area where solvent vapors do not accumulate, and wear a gas mask for organic solvents.
2.Work in an area with fire extinguishing equipment.
3.If symptoms of solvent poisoning occur, seek immediate medical attention.
1.Wipe off moisture, dust, and light oil with a rag, etc.
2.If there is a lot of oil on the surface, wash it with a solvent or detergent and dry it well.
3.Do not use on rubber, plastic or painted parts.
1.Open the paint container and mix with an appropriate stick until uniform.
2.Basically, use undiluted solution.
If it becomes difficult to apply, mix in 5-10% of a special thinner.
3.Use a rather large brush, soak it in thinner and squeeze it well when it becomes soft.
1.Take a small amount of the thoroughly mixed seal peel in a saucer and apply it thickly enough that there is no dripping or running.
2.The trick is to apply one quick coat back and forth because if you go back and forth over one spot too many times, it will peel off on the brush.
3.When applying overlapping coats, make sure the surface is dry before doing so.
4.If the surface dries in about 1 hour after drying, it can be used.
However, it takes about 4-8 hours to dry, depending on the environment.
5.If the dried film starts to peel, it can be repaired by either repainting or brushing on seal peel in place of glue to fill the gaps in the film.
・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.
#Series 3002 SEALPEEL is a transparent liquid, adhesive-type paint at room temperature.
The following three methods of application are available
1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)
16kg can, 3kg can
| Appearance | Opaque colored viscous liquid |
| Stinky | Aromatic smell |
| Boiling point | 108.5℃ |
| Specific gravity | 0.9 |
| Solubility | insoluble in water |
| Flash point | 4.5℃ |
| Point of ignition | 363℃ |
1.When working indoors, make sure the area is well ventilated and free of solvent vapors, and wear a gas mask for organic solvents.
2.Be careful of fire and work in an area with fire extinguishing equipment.
3.If symptoms of solvent poisoning occur, seek immediate medical attention.
1.Wipe off moisture, dust, and light oil with a rag, etc.
2.If there is a lot of oil on the surface, wash it with a solvent or detergent and dry it well.
3.Do not use on rubber, plastic or painted parts.
1.Open the paint container and mix with an appropriate stick until uniform.
2.Use a rather large brush, soak it in thinner and squeeze it well when it becomes soft.
1.Take a small amount of the thoroughly mixed seal peel in a saucer and apply it thickly enough that there is no dripping or running.
2.The trick is to work quickly, as it dries relatively quickly.
・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, provide adequate ventilation until completely dry.
・Store in a cool place out of direct sunlight.
・Be sure to see the SDS.
#Series 8008 SealPeel is an opaque brown liquid paint that can be peeled off at room temperature.
In addition to being effective against acid and alkali solutions, it is particularly effective in masking conversion coatings (black finish).
The following three methods of application are available
1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)
16kg can, 4kg can
| Appearance | Opaque viscous liquid |
| Stinky | Aromatic smell |
| Boiling point | 108.5℃(toluene) |
| Specific gravity | 0.866 |
| Solubility | insoluble in water |
| Volatile | Existence |
| Flash point | 6℃ |
| Point of ignition | 480℃ |
・Urethane, urethane, modified epoxy, acrylic silicone
・Wash primer
・Wood, tools, FRP resin, steps (landing)
・Glass, handrails, (parks, etc.) slip prevention
・Handles, concrete, mats, tiles
・Stone, impact prevention, etc.
Other uses are possible based on your ideas.
・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, provide adequate ventilation until completely dry.
・Store in a cool place out of direct sunlight.
・Be sure to see the SDS.
・Easy to handle with minimal dripping
・A tough, resilient film is formed.
・High frictional resistance and can be used as a non-slip surface
・Keeps rust away
・Excellent insulation, weather resistance (more than 1 year), water resistance, heat resistance, and cold resistance
※The test values below are for reference only and may vary depending on the environment such as temperature and humidity.
| #1002-A | #8500 | |
| Viscosity ｍPa･s | 1300~1600 | 3000~4000 |
| Dryness min | Finger touch10/Curing60 | Finger touch30/Curing120 |
| Coating amount g/m2 | 【Brush coating】996 | 【Brush coating】532(*1) 【スプレー】520(*2) |
| Film thickness mm | 【Brush coating】0.30 | 【Brush coating】532(*1) 【スプレー】520(*2) |
| Outdoor weather resistance | 6 months | 12 months |
(*1)Two coats by brush
(*2)Undiluted solution 1:diluted material 1 (2 coats using the mixture shown at left)
The following three methods of application are available
1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)
16kg can, 4kg can
| Appearance | Clear colorless liquid |
| Stinky | Aromatic smell |
| Boiling point | 108.5℃ |
| Specific gravity | 0.9 |
| Solubility | insoluble in water |
| Flash point | 4.5℃ |
| Flash point | 363℃ |
・Urethane, urethane, modified epoxy, acrylic silicone
・Wash primer
・Wood, tools, FRP resin, steps
・Glass, handrails, (parks, etc.) slip prevention
・Handles, concrete, mats, tiles
・Stone, impact prevention, etc.
Other uses are possible based on your ideas.
・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・取り扱いの都度、容器は密封してください。
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.
・Easy to handle with minimal dripping
・A tough, resilient film is formed.
・High frictional resistance and can be used as a non-slip surface
・Keeps rust away
・Excellent insulation, weather resistance (more than 1 year), water resistance, heat resistance, and cold resistance
・No oil-based materials are used, so there is no risk of undermining.
The following three methods of application are available
1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)
15kg can, 3kg can
The test values below are for reference only and may vary depending on the environment such as temperature and humidity.
| #1002-A | #8501 | |
| Viscosity ｍPa･s | 1300~1600 | 5000～7000 |
| Desiccation min | Feel10/Curing60 | Feel30/Curing120 |
| Coating amount g/m2 | 【Painting with a brush】996 | 【Painting with a brush】0.13 【Spray】0.07 |
| Outdoor weather resistance | 6 months | 12 months |
(*1) 2 coats by brush
(*2) undiluted solution 1 : diluted material 1 (2 coats by the left formula)
| Appearance | Opaque colored viscous liquid |
| Stinky | Aromatic smell |
| Boiling point | 101℃(MCH) |
| Specific gravity | 0.77 |
| Solubility | insoluble in water |
| Flash point | -3.5℃ |
| Point of ignition | 245℃ |
While #1002-A is suitable for use on metal surfaces, #8501 can be used on painted surfaces (*1) (primer) and provides excellent rust and scratch prevention.
Due to its effectiveness, the top coat can be applied immediately after removal.
(*1)Patch test is required since it may adhere to the product depending on the conditions of use.
・Urethane, urethane, modified epoxy, acrylic silicone
・Wash primer
・Wood, tools, FRP resin, steps (landing)
・Glass, handrails, (parks, etc.) slip prevention
・Handles, concrete, mats, tiles
・Stone, impact prevention, etc.
Other uses are possible based on your ideas.
・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed after each handling.
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.
#2001 SealPeel is a clear liquid at room temperature, and the dried film can be easily peeled off as a single film.
It is mainly used for primary corrosion prevention, plating masking, and surface protection of goods.
The following three methods of application are available
1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)
16kg can, 3kg can
| Appearance | Clear and colorless or green |
| Bad smell | Organic solvent smell |
| Boiling point | 90.35℃ |
| Specific gravity | 0.89 |
| Solubility | Water: insoluble, organic solvents: soluble |
| Volatile | existence |
| Flash point | -1℃ |
| Point of ignition | None |
Primary rust prevention, protection, and stain prevention of parts and components
Masking during chrome plating process
・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.
It has a proven track record as a masking agent for chrome plating.
The environmentally friendly design allows for use by companies that have acquired ISO certification or have already obtained certification.
The following three methods of application are available
1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)
16kg can, 3kg can
Masking during chrome plating
・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.
Forms a translucent or red film to protect against dirt, scratches, rust, and chemicals.
The following three methods of application are available
1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)
16kg缶、3kg缶
| Appearance | Clear colorless or red |
| Bad smell | Solvent smell |
| Boiling point | 78.7℃ |
| Specific gravity | 0.77 |
| Solubility | Water: insoluble Solvent: soluble |
| Flash point | 5℃ |
Masking during chrome plating
・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.
It can be used for a wide range of applications including furniture, instruments, plastics, and painted surfaces.
Viscosity adjustment facilitates spray application, which was an issue with #8501.
It is weather resistant and protects objects from rust and stains even outdoors (limited period).
In terms of film thickness, adhesion, and peelability, this product is standard in the SEALPEEL product line and is easy to handle.
Excellent heat and chemical resistance.
The following three methods of application are available
1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)
14kg can, 3kg can
| Appearance | Clear colorless or red |
| Bad smell | Solvent smell |
| Boiling point | 101℃ |
| Specific gravity | 0.89 |
| Solubility | Water: insoluble Solvent: soluble |
| Flash point | －4℃ |
| Point of ignition | 258℃ |
Prevention of stains and primary rusting of jigs and construction materials/construction equipment, rental equipment, etc.
・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.
Protective Coating Seal Peel Go to the SDS download form page.
Password is required to view.
Please contact us by e-mail or phone from the above page.
TEL:045-211-6740(Representative)
FAX:045-211-6741
Office hours: [weekdays].9:00~17:00（JST）
